Investigation on the effectiveness of the repair method 8.3 “Corrosion protection by increasing the electrical resistivity” in chloride-containing concrete Part 2: Chloride redistribution in concrete after application of a system sealing surface protective coating

This DFG-funded research project aimed to gain a better understanding of the mechanisms of the W-Cl repair principle within the framework of fundamental investigations, to contribute to the creation of the necessary basis for a broader application of the repair principle in practice. The focus was on the development of a model to describe the chloride redistribution after the application of a system sealing surface protective coating. On the basis of Fick's second law of diffusion, a mathematical model with a self-contained analytical solution was developed, with the help of which the chloride redistribution after application of a system sealing surface protective coating can be calculated under the idealized assumption of complete water saturation of the concrete. Furthermore, the influence of the dehydration of the concrete, expected as a result of the application of the repair principle W-Cl, on the chloride redistribution was investigated. On the basis of laboratory tests and numerical simulations, material-specific reduction functions were developed to quantify the relationship between the chloride diffusion coefficient and the ambient humidity.     

近距离煤层煤柱下应力分布和巷道支护技术

针对和尚嘴煤业近距离煤层煤柱下掘进巷道变形大的问题,在介绍地质力学特征的基础上,采用数值模拟分析上部煤层不同方式采动后,采空区和煤柱在下部煤层的应力分布情况。分析煤柱下巷道变形特点和支护要点,结合高预应力强力锚杆支护理论,提出合理的锚网与锚索联合支护设计,现场试验效果明显。     

机制砂混凝土耐磨性的主要影响因素分析及多因素计算模型

本文研究了砂类型、砂率、石粉含量和抗压强度对机制砂混凝土耐磨性的影响,建立了磨损量的多因素计算模型。结果表明:由于含石粉及具有更高的粗糙度和坚固性,石灰岩与辉绿岩机制砂制备的C30、C40混凝土耐磨性比河砂混凝土提高20%以上;在0.40~0.44范围内选取较低的砂率可获得较优的耐磨性;利用石粉含量为5%~11%(质量分数)的机制砂制备混凝土,石粉含量为9%时可获得最佳的混凝土耐磨性,微观分析表明此时混凝土密实度最佳;通过灰色系统理论确定了耐磨性影响因素的影响程度排序为:砂率R₃>压碎值R₂>粗糙度R₁>抗压强度R₅>石粉含量R₄>0.6;对比验证表明提出的混凝土磨损量多因素计算模型具有较高的预测精度和良好的适用性。     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Numerical modeling assessment of mechanical effect in bovine leather drying process

Leather manufacturing involves a crucial energy-intensive drying stage in the finishing process to remove its residual moisture and generates important heat gradients. The numerical model presented in this study has been developed to describe the drying process of porous medium: bovine leather that undergoes deformation due to shrinkage. The mathematical formulation of fundamental heat, mass and momentum transfers’ phenomena during drying summarizes a two-dimensional model considering elastic behavior of bovine leather. The evolution of moisture content, temperature, and mechanical stresses during drying was discussed. The model was validated with experimental results. Numerical simulations show good agreement with experimental results. The study shows that the elastic model keeps the stress sign at the final stage of drying. The deformations induce tensional stresses near the surface equilibrated by compressive stresses within the product. They reached their maximum for normal stresses equal to 5.97 and 3.52?MPa at around 2145 and 868?s, respectively, for normal stresses along x and y directions and then decrease.     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

Hydrogen Peroxide-Preconditioned Human Adipose-Derived Stem Cells Enhance the Recovery of Oligodendrocyte-Like Cells after Oxidative Stress-Induced Damage

Oxidative stress associated with neuroinflammation is a key process involved in the pathophysiology of neurodegenerative diseases, and therefore, has been proposed as a crucial target for new therapies. Recently, the therapeutic potential of human adipose-derived stem cells (hASCs) has been investigated as a novel strategy for neuroprotection. These cells can be preconditioned by exposing them to mild stress in order to improve their response to oxidative stress. In this study, we evaluate the therapeutic potential of hASCs preconditioned with low doses of H₂O₂ (called HC016 cells) to overcome the deleterious effect of oxidative stress in an in vitro model of oligodendrocyte-like cells (HOGd), through two strategies: i, the culture of oxidized HOGd with HC016 cell-conditioned medium (CM), and ii, the indirect co-culture of oxidized HOGd with HC016 cells, which had or had not been exposed to oxidative stress. The results demonstrated that both strategies had reparative effects, oxidized HC016 cell co-culture being the one associated with the greatest recovery of the damaged HOGd, increasing their viability, reducing their intracellular reactive oxygen species levels and promoting their antioxidant capacity. Taken together, these findings support the view that HC016 cells, given their reparative capacity, might be considered an important breakthrough in cell-based therapies.